SEMI International Standards
Standards New Activity Report Form (SNARF)
Date Prepared: 05/01/2020Revised (if Applicable):

Document Number: 6674
SNARF for: New Standard: Specification of ID Marking for Glass Carrier Characteristics of Panel Level Packaging (PLP) Applications

Originating Global Technical Committee: Traceability
Originating TC Chapter: Japan
Task Force (TF) in which work is to be carried out: Panel Level Packaging (PLP) Glass Carrier ID Marking Task Force
Note: If a new task force is needed, also submit a task force organization form (TFOF)

___________________________________________________________________________
1. Rationale:
a. Describe the need or problem addressed by this activity.
(Indicate the customer, what benefits they will receive, and if possible, quantify the impact on the return on investment [ROI] if the Document is implemented.)
The introduction of Panel Level Packaging (PLP) technology is expected to become a critical 3D integration and packaging process. These manufacturing processes require a variety of materials, especially carrier materials for panel processing. Glass materials are commonly used as carrier materials.
Each of these Glass Carriers must be individually identified and managed individually. Standard specifications for 2D Code printed on Glass Carrier are required.



b. Estimate effect on industry.
1: Major effect on entire industry or on multiple important industry sectors - identify the relevant sectors
Sector or Company Information: Middle end of the line and substrate fabricators

c. Estimate technical difficulty of the activity.
II: Some Difficulty - Disagreements on known requirements exist but developing consensus is possible

___________________________________________________________________________
2. Scope:
a: Describe the technical areas to be covered or addressed by this Document development activity. For Subordinate Standards, list common concepts or criteria that the Subordinate Standard inherits from the Primary Standard, as well as differences from the Primary Standard:
This document will specify the ID marking of PLP glass carrier.
The following specifications are defined.
Code type
Code size and shape
Symbol size (number of dots)


b: Expected result of activity
New Standard or Safety Guideline (including replacement of an existing Standard or Safety Guideline)

For a new Subordinate Standard, identify the Primary Standard here:




For Standards, identify the Standard Subtype below:
Specification

Miscellaneous (describe below):

___________________________________________________________________________
3. Projected Timetable for Completion:

a: General Milestones
a. Activity Start: 06/01/2020b. 1st Draft by: 07/01/2020
c. (Optional) Informational Ballot by: d. Letter Ballot by: 10/06/2020
e. TC Chapter Approval By:12/31/2020

_____________________________________________________________________________
4. Liaisons with other Global Technical Committees/TC Chapters/Subcommittees/TFs:
a.
List SEMI global technical committees, TC Chapters, subcommittees, or task forces in your or other Regions/Locales that should be kept informed regarding the progress of this activity. (Refer to SEMI Standards organization charts and global technical committee charters and scopes as needed.)
Panel Level Packaging (PLP) Glass Carrier Task Force
Panel Level Packaging (PLP) Panel FOUP Task Force
North America TC Chapter of Traceability Global Technical Committee
Physical Interfaces & Carriers Global Technical Committee
3D Packaging & Integration Global Technical Committee

b. List any planned Type I Liaisons with external nonprofit organizations (e.g., SDO) that should receive Draft Documents from Standards staff for feedback during this activity and be notified when the Letter Ballot is issued (refer to Procedure Manual 7):


c. Intercommittee Ballots:
will be issued – identify the recipient global technical committee(s):

Identify the recipient global technical committee(s):
3D Packaging and Integration, Physical Interfaces & Carriers
___________________________________________________________________________
5. Safety Considerations:
The resulting document is expected:
NOT to be a Safety Guideline

NOTE FOR "to be a Safety Guideline": When all safety-related information is removed from the Document, the Document is NOT technically sound and complete - Refer to Section 15.1 of the Regulations for special procedures to be followed.

NOTE FOR "NOT to be a Safety Guideline": When all safety-related information is removed from the Document, the Document is still technically sound and complete.

___________________________________________________________________________
6. Intellectual Property Considerations:
a. For a new Standard or Safety Guideline and for any part to be modified or added in a Revision of published Standards and Safety Guidelines:
the use of patented technology is NOT required.

If "patented technology is intended to be included in the proposed Standard(s) or Safety Guideline(s) " is selected above, then also check one:


b. For Revision, Reapproval, Reinstatement, or Withdrawal of existing Standard(s) and Safety Guideline(s):
there is no known material patented technology necessary to use or implement the Standard(s) and Safety Guideline(s)

c. The body of the Document and any Appendices, Complementary Files, Related Information sections, or Various Materials that may or may not be a part of the Document by reference:
the incorporation of Copyrighted Item will NOT be required



NOTE FORthe use of patented technology or the incorporation of Copyrighted Item(s) is NOT required’: If in the course of developing the Document, it is determined that the use of patented technology or Copyrighted Item(s) is necessary for the Document, the provisions of Regulations 16 must be followed.

NOTE FORwill incorporate Copyrighted Item’: A copyright release letter must be obtained from the copyright owner prior to publication.

___________________________________________________________________________
7. Comments, Special Circumstances:

__________________________________________________________________________
8. TC Member Review:
took place between (put dates below) before approval by the GCS, or

Member Review Start Date; 07/03/2020
Member Review End Date: 07/16/2020

NOTE FOR ‘TC Member Review’ is required by the Regulations for a period of at least two weeks
before approval of a new, or a major revision of an existing, Standard or Safety Guideline. (Refer to Regulations 8.2.1)
__________________________________________________________________________

9. SNARF Approval Dates:
TC Chapter or GCS08/20/2020
Recorded in TC Minutes

__________________________________________________________________________

10. SNARF Extension Dates:
TC Chapter Extension Granted on
Extension Expires on

Attach Pictures and Files here: